Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Don't underestimate the forklift at the office. If the procedure is bad, there will certainly be significant crashes in mins, and there are many accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the path and holds on the roadside rack, which practically causes an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and then begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be safe prior to starting.
3. When the forklift begins with a load, the motorist ought to first validate that the load is secure and reputable.
4. The beginning needs to be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the lots is traveling, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork ought to be decreased to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to shut off the fire and slide, and it is restricted to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to follow the website traffic rules in the manufacturing facility and have to maintain a particular safety distance from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not prevent the driving, and the gantry needs to be effectively slanted back. The lots will not be increased except when stacking or packing. .
8. The elevation of the lots must not obstruct the driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving speed of the forklift in the factory area is 5 km/h, and it has to drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, raised or driven, it is prohibited for workers to stand on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a timely fashion, and they will never run with health problems or conceal them.

filling and dumping.
1. When fork-loading products, the distance in between the two forks need to be readjusted as needed to make the lots of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be kept in mind that the fork suggestion need to not touch other products or things. The tons needs to be stabilized with very little back tilt of the gantry to make sure that the tons does not glide in reverse. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is forbidden, and it is banned to use forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to utilize the brake inertia to slip, place, round or roll items. .
10. It is not permitted to make use of forks to select, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or depress the parking brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the vehicle's view and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water must be added.
2. Check the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage should additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send a signal Stand-on Electric Pallet Stacker at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move forward, if they come across large or hefty items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be Electric Forklift Truck for Warehouse complied with in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not allowed to utilize stopping force to exile round or easy-to-roll things.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on inclines
.
Vehicle parking is not allowed under the list below conditions.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal incline higher than 5%.
3. When there is an challenge on one side of the road, the opposite side of the area with the very same length as the obstacle should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844